Get 100% Authentic NACE NACE-CIP2-001 Dumps with Correct Answers
New Training Course NACE-CIP2-001 Tutorial Preparation Guide
NEW QUESTION # 31
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
- A. Redo the pre-cleaning based on the other inspectors results
- B. Review the specification with the other inspector to see what method was specified
- C. Advise the other inspector he is using an incorrect method
- D. Advise your QC Manager to change the ITP to the use of the salt smart meter
Answer: B
NEW QUESTION # 32
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. powder coatings.
- B. urethanes.
- C. epoxies.
- D. inorganic zincs.
Answer: D
NEW QUESTION # 33
It is always possible to see moisture on a steel substrate:
- A. False
- B. True
Answer: A
NEW QUESTION # 34
Which product, is used in conjunction with other coatings such as FBE when the lines run through wetlands or a body of water?
- A. Coal Tar Enamel
- B. Concrete
- C. 2-Layet Polyethylene (PE)
- D. 3-Layet Polyethylene (PE)
Answer: B
NEW QUESTION # 35
Which surface preparation method uses a dilute acid solution to remove laitance and I roughen the concrete surface?
- A. High-pressure water washing
- B. Acid etching
- C. Sacking
- D. Stoning
Answer: B
NEW QUESTION # 36
On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?
- A. Heat-shrink sleeves
- B. Concrete
- C. Coal Tar Enamel
- D. Liquid epoxies
Answer: D
NEW QUESTION # 37
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Ultra Sonic DFT Gauge
- B. Tooke Gauge
- C. Eddy Current Gauge
- D. Magnetic Gauge
Answer: B
NEW QUESTION # 38
NACE Standards include:
- A. a) & b)
- B. a) only
- C. Standard Practices
- D. Material Requirements
Answer: A
NEW QUESTION # 39
A single component water borne acrylic coating cures by:
- A. Oxidation
- B. Coalescence
- C. Solvent Evaporation
- D. Co-Reaction
Answer: B
NEW QUESTION # 40
You can use magnifiers to examine all of the following EXCEPT
- A. Mill scale
- B. Blisters
- C. Surface profile
- D. Surface cleanliness
Answer: D
NEW QUESTION # 41
You are the NACE Level 2 Inspector with the final responsibility to prepare the final report for a very large structural steel shop project which has gone very well. It is due next week. The work has been ongoing for two years and several NACE Level 1 Inspectors have worked under your supervision throughout the project. You find you are missing one week of daily reports for the night shift from the very beginning of the project and despite your best efforts they are cannot found.
You FIRST preferred course of action is to:
- A. Do not complete your report until they can be found
- B. Re-create the reports as not much was going on during night shift anyway
- C. Plainly state in your report that they are missing
- D. Use creative writing to cover over the fact they are missing
Answer: C
NEW QUESTION # 42
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
- A. High-pressure water washing
- B. Sacking
- C. Acid etching
- D. Stoning
Answer: B
NEW QUESTION # 43
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Request clarification from the specifier
- B. Call your supervisor
- C. Enforce the additional requirement
- D. Ignore the additional requirement
Answer: C
NEW QUESTION # 44
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Consult your supervisor
- B. Review the NCR with the other Inspector
- C. Verbally challenge the NCR
- D. Request a re-blast of the item in question
Answer: A
NEW QUESTION # 45
Coating surveys may include which steps?
Select All That Apply:
- A. Summarize the collected data
- B. Evaluate the coatings performance
- C. Develop a survey plan
- D. Schedule the remedial work
Answer: A,B,C,D
NEW QUESTION # 46
......
Dumps of NACE-CIP2-001 Cover all the requirements of the Real Exam: https://www.prep4sures.top/NACE-CIP2-001-exam-dumps-torrent.html
Correct Practice Tests of NACE-CIP2-001 Dumps with Practice Exam: https://drive.google.com/open?id=1YV7WlkFRCHIsaRDOSF-7YUM8kg4v8bHM