NS0-184 PDF Dumps Real 2023 Recently Updated Questions
Released Network Appliance NS0-184 Updated Questions PDF
NEW QUESTION # 10
Click the Exhibit button.
You are installing a new FAS cluster. The management network must be on tagged VLAN 11 for remote administration by a service provider.
Referring to the exhibit, which two ports will allow service provider access to both cluster and node management LIFs? (Choose two.)
- A. e0M
- B. e0a-11
- C. e0b-11
- D. e0M-11
Answer: A,D
NEW QUESTION # 11
After moving a new AFF A400 cluster into production, the administrator notices error events in ONTAP System Manager regarding SAS HA issues.
In this scenario, which NetApp tool would have identified these errors after the installation process?
- A. ONTAP System Manager
- B. Cloud Manager
- C. Active IQ Unified Manager
- D. Active IQ Config Advisor
Answer: A
NEW QUESTION # 12
You are installing a new ONTAP 9.7 cluster by following the installation and setup poster. You are ready to complete the initial cluster setup. You have connected your laptop to the management switch. However, when browsing the network, you are unable to discover the ONTAP controllers.
Which statement explains this behavior?
- A. You do not have network discovery enabled.
- B. You do not have a static IP address.
- C. You do not have IPv6 configuration set.
- D. You do not have a default gateway set.
Answer: D
NEW QUESTION # 13
You use the system health subsystem show command to troubleshoot your newly installed ONTAP cluster.
In this scenario, which two health outputs would this command show you? (Choose two.)
- A. node CPU utilization
- B. shelf connectivity
- C. cluster switch cabling
- D. data switch cabling
Answer: A,B
NEW QUESTION # 14
You have a 4-node ONTAP 9.8 cluster with a FAS8700 HA pair that serves iSCSI LUNs. You are adding a new AFF A250 HA pair to the cluster with new iSCSI SAN LIFs. You need to allow non-optimized data paths from the AFF A250 nodes to the existing LUNs on the FAS8700 nodes.
In this scenario, which two ONTAP configuration settings must you verify? (Choose two.)
- A. port sets
- B. switch zoning
- C. reporting nodes
- D. failover groups
Answer: A,D
NEW QUESTION # 15
You have just racked a new 6-node switched cluster with ONTAP 9.7. You need to configure the cluster switches.
In this scenario, which two elements would be used to complete the configuration? (Choose two.)
- A. rlogin
- B. serial port
- C. SFP+ port
- D. SSH
Answer: B,D
NEW QUESTION # 16
You are asked to add a new HA pair to an existing 2-node switchless AFF A220 cluster. You must first convert to a 2-node switched cluster using Broadcom BES-53248 cluster switches.
Which two conditions must be fulfilled before you start the migration? (Choose two.)
- A. All cluster LIFs must have an MTU size of 1500.
- B. All cluster LIFs must be in the up state and on their home ports.
- C. The 2-node switchless configuration must be properly set up and functioning.
- D. The "Enabled Switchless Cluster" option must be manually set to "false".
Answer: B,C
NEW QUESTION # 17
You want to disconnect a DS224C shelf with 3.8 TB NetApp Storage Encryption (NSE) SSDs to an AFF A300 HA pair with two DS224C shelves with 3.8 TB SSDs without NSE in one stack.
In this scenario, how would you add the shelf?
- A. License NSE and add the shelf to this HA pair as a new stack.
- B. Connect the shelf to an HA pair with NSE drives.
- C. Add the shelf to the existing stack.
- D. Create a new stack on the HA pair to add the shelf.
Answer: C
NEW QUESTION # 18
You have a new 2-node FAS8700 ONTAP 9.8 cluster. One of the nodes has 24x16 TB NL-SAS disks assigned and available for a new aggregate. You created the aggregate with one RAID group and two spare disks.
In this scenario, how many data drives are in the aggregate?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION # 19
You have a 2-node FAS8300 ONTAP 9.8 cluster that serves SMB shares. You are configuring interface groups for higher performance and resiliency.
Which two NetApp best practices should you follow to satisfy these performance and resiliency requirements? (Choose two.)
- A. Use ports with different chipsets.
- B. Use ports from the same NICs.
- C. Use ports from different NICs.
- D. Use ports with the same chipsets.
Answer: C,D
NEW QUESTION # 20
You are installing a new six-node ONTAP 9.8 cluster. You have completed the initial configuration of the cluster interconnect switches and the ONTAP cluster.
In this scenario, which feature should you enable?
- A. cluster switch logging
- B. data center bridging protocol
- C. IPv6 on all cluster ports
- D. cluster switch health monitor
Answer: D
NEW QUESTION # 21
While testing a recently installed FAS8700 cluster, a node fails. You now need to replace the impaired node.
In this scenario, which two statements are true? (Choose two.)
- A. A controller model of the same type must be used to replace the impaired node.
- B. The boot device must remain intact and must not be removed from the impaired node.
- C. You can change any drives or disk shelves as part of this replacement procedure.
- D. You must move the boot device from the impaired node to the replacement node.
Answer: A,D
NEW QUESTION # 22
You want to verify that connections are cables correctly and that shelf IDs are unique within an HA pair.
Which tool would be used to accomplish these tasks?
- A. Cloud Insights
- B. System Diagnostics
- C. Active IQ Unified Manager
- D. Active IQ Config Advisor
Answer: B
NEW QUESTION # 23
A customer is creating a new SVM to host iSCSI LUNs for a Hyper-V cluster. You need to successfully map the new LUNs and make them visible to the Hyper-V cluster.
In this scenario, which host information is required to accomplish this task?
- A. WWPNs
- B. IQNs
- C. host names
- D. WWNNs
Answer: C
NEW QUESTION # 24
Click the Exhibit button.
Referring to the exhibit, what information is forwarded to syslog after you enter the scripted install commands? (Choose two.)
- A. AutoSupport messages
- B. EMS messages
- C. SNMP traps
- D. command history
Answer: A,D
NEW QUESTION # 25
On which type of network interfaces are the cluster interconnect LIFs created?
- A. on a UTA port shared with other LIFs
- B. on a physical port
- C. on an FC or FCoE port
- D. on an interface group
Answer: D
NEW QUESTION # 26
After adding two nodes to an FC-enabled cluster, the storage administrator wants to ensure that existing LUNs can use paths on the new nodes.
What is required to complete this task?
- A. Rescan the bus on the hosts by using the rescan-scsi-bus.sh script.
- B. Use the storage port rescan command.
- C. Use the lun bind create command.
- D. Use the lun mapping add-reporting-nodes command.
Answer: B,D
NEW QUESTION # 27
You installed a new pair of Cisco 92300YC cluster switches at a customer's site. Before you install any files on the switch, you want to view the current configuration.
In this scenario, which command would you use to accomplish this task?
- A. fabricshow
- B. show running-config
- C. switchcfgshow
- D. config show
Answer: C
NEW QUESTION # 28
Click the Exhibit button.
You are adding new DS224C shelves in a new stack to your cluster with FAS8060 controllers running ONTAP 9.7.
Referring to the exhibit, which two actions should be performed to the cluster before installing the new shelves? (Choose two.)
- A. Enable in-band ACP.
- B. Move the SAS cables to a new stack.
- C. Disable out-of-band ACP.
- D. Remove the Ethernet cables.
Answer: B,C
NEW QUESTION # 29
You are installing a new AFF A400 cluster for a customer. The customer indicates that they want to take advantage of AutoSupport On Demand.
In this scenario, which AutoSupport transport protocol must you use?
- A. FTP
- B. HTTP
- C. SMTP
- D. HTTPS
Answer: D
NEW QUESTION # 30
......
The NS0-184 exam covers a range of topics related to NetApp storage systems, including cluster setup, hardware installation, networking, and data protection. Candidates must have a thorough understanding of these topics to pass the exam and obtain certification. The exam consists of 60 multiple-choice questions, and candidates have 1.5 hours to complete it. To pass the exam, candidates must score at least 70%.
Network Appliance NS0-184 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
| Topic 6 |
|
NS0-184 Dumps and Practice Test (60 Exam Questions): https://www.prep4sures.top/NS0-184-exam-dumps-torrent.html
Guide (New 2023) Actual Network Appliance NS0-184 Exam Questions: https://drive.google.com/open?id=1vdbTgFzYydRynoMG7vV_0MXlaEQU2rbh